22 thoughts on “Unlock protected block in simatic manager (Siemens S7 PLC) using Microsoft Access

    Vinicius Barboza

    (December 25, 2018 - 10:06 pm)

    Is it work with Simotion Scout too?

    Adrian Ramirez

    (December 25, 2018 - 10:06 pm)

    Thanks a lot

    Abhishek Yadav

    (December 25, 2018 - 10:06 pm)

    Is there any way to unlock protected block in TIA

    Kiran KMNS

    (December 25, 2018 - 10:06 pm)

    we are using Siemens s7300 plc. it is asking password while trying to save the project. we have no back up with us. is there any solution?

    Ömer KARACAN

    (December 25, 2018 - 10:06 pm)

    Thank you man.

    Ahmed Imraj

    (December 25, 2018 - 10:06 pm)

    what is the procedure for siemens tia v13

    Patel Vipul

    (December 25, 2018 - 10:06 pm)

    hi
    how can i contact you?

    tajak

    (December 25, 2018 - 10:06 pm)

    Is there any way how to open SFC and SFB system blocks?

    mt mn

    (December 25, 2018 - 10:06 pm)

    thank you so much nice job

    deshabandhu nayak

    (December 25, 2018 - 10:06 pm)

    hi can please tell me how protect with password siemens FBs and FCs

    Avinash Jadhav

    (December 25, 2018 - 10:06 pm)

    dear sir, please give me info abot HOW TO CRACK/UNLOCK FABRIWIN PROTECTION LOCK?
    my sir installed Fabriwin Software in absence of me. then what happens that laptop suddenly have a board problem, so i replaced that software installed harddisk to the same model another laptom.. all ok,, but when i open that Fabriwin software it says Protection lock not found. but on old laptop it doesnt say this messg when i was opening that software (FABRIWIN). please help to to find me solution sir.. please

    Tepeido Nakara

    (December 25, 2018 - 10:06 pm)

    Awesome man !!!!

    Ajai Shukla

    (December 25, 2018 - 10:06 pm)

    great job …please upload a video how to crack s7-200 password

    Ajai Shukla

    (December 25, 2018 - 10:06 pm)

    thanks

    adem taş

    (December 25, 2018 - 10:06 pm)

    Thank you frends.SUBBLK.DBF is not opened by Microsoft Acces 2013 But It is opened by Microsoft Acces 2010.

    Thank so Much…

    Nousheeb Hamza

    (December 25, 2018 - 10:06 pm)

    many thanks..brother

    Jie Ding

    (December 25, 2018 - 10:06 pm)

    2007 works! Thanks so much

    keshav sharma

    (December 25, 2018 - 10:06 pm)

    Thank you very much for this amazing trick!!! yes it is working in Access 2007. But when i tried it in Access 2013 , even not able to open .DBF file, it's shows error…..

    Yeldos Baltakov

    (December 25, 2018 - 10:06 pm)

    Thank you very much! You are genius! God luck!

    Mustafa Akman

    (December 25, 2018 - 10:06 pm)

    Good jop. access 2007 working

    Imran Shahzada

    (December 25, 2018 - 10:06 pm)

    Its not Opening its shows the following Error….
    Expression failed..
    Retry to debugge the application -JIT must be enabled…please explain Thanks

    Parthib Vinayak

    (December 25, 2018 - 10:06 pm)

    Good job. Will it work in MS access 2013..?  Its not working in MS access 2013 for me.

Leave a Reply

Your email address will not be published. Required fields are marked *